TBR Combinedflow Closed Cooling Towers Home > Products & Services >  TBR Combinedflow Closed Cooling Towers
 

 

Principle of operation
Basic operating principle of closed cooling tower is as follows
The process medium customers need is circulated inside the device. Heat medium goes through the heat exchanger coil, disperses the heat to the external air and spray water, is discharged from the export of the lower part of the coil after cooled.
The fluid customers need to be cooled flows inside the coil, without contact with the outside world, is protected from contamination , to satisfy the good working condition of the stringent system requirements;
The spray water is pumped from bottom of the device by the special low head and high flow pump out ,sprayed to the out surface of the coil by the up water distribution system , to ensure full coverage, enhance heat transfer, and reduce the possibility of forming scale ;
The outside fresh cold air goes into the device from the lower part of the equipment , through the coil surface, evaporates a little part of the spray water. As the latent heat of vaporization of water is very large, can effectively exchange the heat inside the coil outside, and ultimately discharge the hot and humid air out of the device from the fan.

Efficient heat exchange coil
For the heat transfer is concerned, the first need is enough heat transfer area, with sufficient heat transfer area, it will be a fundamental guarantee for the effect of heat transfer; heat exchanger coil is made of high quality low carbon steel, hot dip through the whole zinc processing, three rigorous testing pressure is 2.5Mpa through the production process.
Tubes using oval tube, both ends are bended directly by the tubes, reducing the possibility of leakage caused by welding elbow. Heat exchanger coil group with snake-like tube design, moderate slope along the flow direction, in order to facilitate coil water.

High-quality energy-efficient fan and duct
TBT closed cooling tower’s cooling fan use the wing-type hollow dedicated and efficient axial special for cooling tower fan which is made of aluminum alloy by whole stretching, fan angle can be adjusted depending on the device line. After overall dynamic balance and static balance of high-strength test, the fan is no longer disassemble ,and before assembled to the cooling tower, again checking the static balance, to ensure reliable performance, blades are made of hollow aluminum alloy material, the central hub is made of high-strength steel, to ensure the fan’s sufficient strength when rotating with high speed. Streamlined wing blades, to ensure adequate air flow and air pressure at the same time, reducing fan noise. Venturi tube using duct design, effectively improve the efficiency of the fan more than 5%, made of galvanized steel, the full use of the gas flow duct averaging theory, practical experience with engineering design and measured data, the use of inner curve elliptic curve, and the use of line compared to the natural diffusion hairdryer, remove the air duct off the wall phenomenon, reducing the eddy current region, the central duct significantly reduced negative pressure area, the outlet cross-section of wind speed distribution tends to have , the practical application of testing, the duct is greater than 30% of the kinetic energy recovery.
Axial fan is installed on top of cooling towers. Fan bracket is fixed on the cooling tower frame, making it one solid structure, and is conducive to the future demolition, replacement, repair and maintenance.

Motor
Outdoor totally enclosed motors used (including fan and pump motors), class “IP55” protection, class ”F” insulation, oil-free maintenance, high reliability, trouble-free operation for a long time.

Fan drive
Variable speed belt drive used, drive efficiency up to 99%, driven by stable performance and high reliability. Compared to the direct drive and gear-driven blower, it makes lower noise, needs lower costs and easier maintenance. Through adjustable motor frame, easy to adjust the belt tension, extend belt life.

Bearing
NTN Heavy Duty Self-aligning ball bearings, are imported from Japan, high strength, excellent workmanship, long life. Bearing oil hole extending through the fuel line, is arranged out of the equipment, easy to refuel, even if the device is running.

Pump
Due to the special requirements of evaporative condenser, TBT series use special low head, high flow high efficiency pumps, in a large spray of water to ensure adequate case and still maintain a smaller power consumption, which greatly improved the equipment energy-saving effect. Pump motor for outdoor design, protection class IP55.Pump use Bergman mechanical seal, wear resistance, long life. Pump’s lowest point settings drain plugs, drain off easily to prevent the volute from cracking by the stocked water in the winter.

Corrosion resistance, Anti-rust
Full account of the rust problem, the skeletons, panels and other steel products use galvanized steel, and meet the temperature requirements. Therefore, this device has good corrosion resistance, anti-rust ability. To improve corrosion resistance, low temperature and the ability of the galvanized steel to adapt to environmental conditions, use thick galvanized steel materials, and in the process prevent damaging surface of the steel from scratches , and maintain galvanized steel bright primary colors , making the tower looks nice.

Beautiful appearance, easy maintenance, low running costs
In the structure, the cooling tower introduces foreign advanced technology developed structural steel and galvanized steel plate panel structure, and advanced external fan oiling system (oil gun injection), making the operation and the maintenance much easy, with the advanced level of this product in heat transfer, energy saving field, making the running costs greatly reduced, and the beautiful shape can be in perfect harmony with the building, saving additional costs.

Easy installation, short construction period
As the use of advanced process module theory and special design, all models in the cooling tower can be delivered directly in the form of finished product (divided into two parts).They are stitched with flange in the field, can be lifted directly to the place, so can reduce the construction period, and save the expenditure.

Principle of operation
Basic operation principle of closed cooling tower is as follows:
The process medium customers need is circulated inside the device. Heat medium goes through the heat exchanger coil, disperses the heat to the external air and spray water, is discharged from the export of the lower part of the coil after cooled.
The fluid customers need to be cooled flows inside the coil, without contact with the outside world, is protected from contamination , to satisfy the good working condition of the stringent system requirements;
The spray water is pumped from bottom of the device by the special low head and high flow pump out ,sprayed to the out surface of the coil by the up water distribution system , to ensure full coverage, enhance heat transfer, and reduce the possibility of forming scale ;
Both sides and top of the unit lower are equipped with air inlet. The outside fresh cold air goes into the device from the lower part of the equipment , through the coil surface, evaporates a little part of the spray water. As the latent heat of vaporization of water is very large, can effectively exchange the heat inside the coil outside, and ultimately discharge the hot and humid air out of the device from the fan.

Efficient heat exchange coil
For the heat transfer is concerned, the first need is enough heat transfer area, with sufficient heat transfer area, it will be a fundamental guarantee for the effect of heat transfer; heat exchanger coil is made of high quality low carbon steel, whole hot-dip galvanized, three times 2.5Mpa pressure rigorous tested through the production process.

Packing
Use new PVC packing, do not add recycled materials.
Filler piece of physical and chemical properties shall meet or exceed the relevant provisions of Energy Power Planning Council DL/T742-2001《plastic parts and technical conditions》. Sheet density is not greater than 1.55g/cm3, plain film tensile strength is not less than 40MPa, flame oxygen index is not less than 35.
The substrate thickness is not less than 0.4mm before forming packing blocks.
Packing is glued into blocks, bonding rate of is not less than 90%.
Packing block level compression strength ≥ 300kg/m2.

High-quality energy-efficient fan and duct
The TBR closed cooling tower’s cooling fan use the wing-type hollow dedicated and efficient axial special for cooling tower fan which is made of aluminum alloy by whole stretching, fan angle can be adjusted depending on the device line. After overall dynamic balance and static balance of high-strength test, the fan is no longer disassemble ,and before assembled to the cooling tower, again checking the static balance, to ensure reliable performance, blades are made of hollow aluminum alloy material, the central hub is made of high-strength steel, to ensure the fan’s sufficient strength when rotating with high speed. Streamlined wing blades, to ensure adequate air flow and air pressure at the same time, reducing fan noise. Venturi tube using duct design, effectively improve the efficiency of the fan more than 5%, made of galvanized steel, the full use of the gas flow duct averaging theory, practical experience with engineering design and measured data, the use of inner curve elliptic curve, and the use of line compared to the natural diffusion hairdryer, remove the air duct off the wall phenomenon, reducing the eddy current region, the central duct significantly reduced negative pressure area, the outlet cross-section of wind speed distribution tends to have , the practical application of testing, the duct is greater than 30% of the kinetic energy recovery.
Axial fan is installed on top of cooling towers. Fan bracket is fixed on the cooling tower frame, making it one solid structure, and is conducive to the future demolition, replacement, repair and maintenance.

Motor
Outdoor totally enclosed motors used (including fan and pump motors), protection class of IP55, class ”F” insulation Oil-free maintenance, high reliability, trouble-free operation for a long time.

Fan drive
Variable speed belt drive used, drive efficiency up to 99%, driven by stable performance and high reliability. Compared to the direct drive and gear-driven blower, it makes lower noise, needs lower costs and easier maintenance. Through adjustable motor frame, easy to adjust the belt tension, extend belt life.

Bearing
NTN Heavy Duty Self-aligning ball bearings, are imported from Japan, high strength, excellent workmanship, long life. Bearing oil hole extending through the fuel line, is arranged out of the equipment, even if the device is running, also easy to refuel.

Belt
Multi-groove neoprene polyester lines efficient joined belt, are imported from Israel, even by force, long life, good synchronism, easy to adjust. Belt tension adjustment does not require going into the device.

Pulley
The aluminum alloy pulleys are used in the hot and humid environment within the device, which effectively improve the corrosion resistance.Pump
Due to the special requirements of closed cooling tower, the TBR series use special low head, high flow high efficiency pumps, in a large spray of water to ensure adequate case and still maintain a smaller power consumption, which greatly improved the equipment energy-saving effect. Pump motor for outdoor design, protection class IP55.Pump use Bergman mechanical seal, wear resistance, long life. Pump’s lowest point settings drain plugs, drain off easily to prevent the volute from cracking by the stocked water in the winter.

 

TBR catalog Download

 
Wuxi TENO Cooling Equipment Co., Ltd.                              All Rights Reserved.                                                         Tel: 0510-87693688 苏ICP备10018658号
Address:No.105,East Zhenfeng Road, Xushe Industry Zone,Yixing City, Jiangsu Province, China, 214242        Fax:0510-87698699        E-mail:marketing@wuxiteno.com